Skip to main content

Hydraulic System Adjustment And Accumulator Pressure Checking

Sometimes if Guillotine shearing machine model QC11K-30*2500mm or QC11K-30*3200mm hydraulic systems occurs problems ,how to adjustment and how to Accumulator pressure checking? Don’t worry.

Turn on the power, select the switch to set the “jog position” and jog the “Jog on” and “Jog on” buttons, and the solenoid action should match the solenoid action table. The system uses a direct-current wet electromagnet. It can be used with a small iron such as a short saw blade to rest on the examined magnet to see if there is a suction force to judge whether it is energized or not, but when the knife holder presses the lower (or upper) limit switch It is normal for the electromagnet to have no action when the “point up” (or down) button is pressed.

Accumulator gas pressure check The nitrogen pressure of the accumulator needs to be checked regularly (about 30 days inspection), using the accumulator's nitrogen accumulator tool (the tool is placed in the accessory box), the tool's Use the instructions for use of the inflator. If the nitrogen pressure is less than 7MPa, it should be added.

Accumulator Charge When the machine is in use (or after the machine is repaired), if the accumulator pressure is insufficient (or need to be recharged), the oil should be filled in a timely manner. The specific procedure is: The rack runs to the top dead point. Start the oil pump, place the changeover switch in the cutting position, press the “filling button” button on the control panel, and release the button when the pressure gauge shows 9MPa. 

Accumulator charging In the case of machine maintenance, commissioning or use, if you need to inflate the accumulator, follow the procedure below. Two 16L accumulators are used in the system setup. When inflating, after installing the inflation tool on the nitrogen bottle and accumulator, open the nitrogen bottle switch and observe the pressure gauge connected to the accumulator inflation valve. When the pressure gauge shows 6.5MPa, release the button and complete the inflation. Inflatable tool, tighten the accumulator gas filling valve nut. 

If the nitrogen pressure in the nitrogen bottle is low, the above process can be repeated until the use pressure is reached.

Related Hydraulic Shearing Machine:
QC11K-CNC Hydraulic Guillotine Shearing Machine-DELEM DAC360 System
QC11K-NC Hydraulic Guillotine Shearing Machine-E21S system
Labels:

Comments

  1. BEST KATHA GHOROctober 10, 2020 at 3:06 AM

    Really it was an awesome article. Thank you so much for the post it is very helpful, Keep posting such type of articles as Machining

    ReplyDelete

Post a Comment

Popular posts from this blog

Fiber Laser Cutting Machine

Nowadays laser cutting machine is more and more widely used, as it is with high speed, high precision and automation. It can save manpower and improve production efficiency.  The laser is shot from laser generator, through optical system, focus to high power and density laser beam. The beam shoots on surface of workpiece and makes it reach melting point or boiling point, at the same time, the high pressure gas which is on the same axis with laser beam blow the melting or pneumatolytic metal away. That is the basic reason of laser cutting. According to the laser generator, there are two types – CO2 type & fiber type. The frequency of the CO2 laser requires higher wattage of lasers to penetrate through metals. CO2 laser systems are best suited to cutting wood, acrylic, plastic, and fabric.  Fiber laser cutting machine  is much more energy saving. In the situation that reaches same performance, whole fiber cutting can save around 70% energy than CO2 type. The wattage can...
40 comments
Read more

6mm Hydraulic Shearing Machine With Estun E21s

6mm is a common thickness in sheet metal manufacturing. 6mm  hydraulic shears  is also a popular size in shearing machine. GLDMA can offer 6mm*2500mm, 6mm-3200mm, 6mm*4000mm, 6*5000mm different sizes of worktable, to satisfy variety of plate cutting demands. GLDMA Q12K series swing shearing is standard with Estun E21s system, which can control backgauge and the ordinary motor or frequency converter. Finished parts count and 40 program store functions can support common cutting task much more continuous, so that improve daily producing efficiency and save labor cost. There are also other advanced  shearing machine controller  to choose, like Estun E200ps, Delem DAC 310s. E200ps can realize servo control on X axis (backgauge), the cutting speed and precision are in a higher level. DAC 310s is with control of blade clearance, and the program storage is improved to 100 steps each. Client can choose the suitable model based on their own requirement and budget. 6mm hydra...
12 comments
Read more

Automatic sheet metal bending machine

MB8 series sheet metal press brake with Delem DA56S CNC system Main motor: Siemens Germany Valve: Bosch Rexroth Germany Oil pump: Sunny America Oil tube connectors: EMB Germany Electrics: Schneider, France MB8 CNC Automatic 3+1 Axis Hydraulic Sheet Metal Press Brake Bending Machine With DA56S System Introduction 1. The design meets EU international streamlined design. The fuselage eliminates internal stress by annealing and ensures higher precision and strength. All machines are designed using SOLID WORKS 3D programming to make worktable high rigidity and the whole work More scientific. 2. The MB8 series automatic sheet metal electro-hydraulic bending machines use CNC control system (Delem DA56s from Holland) to help you increase your productivity and keep the lowest cost and lower maintenance costs.High quality and repetitive bending is obtained by using synchronized cylinders and valves (Bosch Rexroth from Germany). 3. The latest high frequency response hyd...
9 comments
Read more