Skip to main content

How to Regulate the Operation of Iron Worker Machine

Technical Specification
1. Before driving, you should check whether the punching and shearing machine transmission components and the connecting screws and pin shafts are loose. Electrical grounding is intact.
2. Lubricate all departments before starting work, drive for two to three minutes, and work without problems.
3. Do not overload, hardened steel is strictly prohibited punching.
4. Wear gloves and wear labor protection when working. Sandals and slippers are strictly prohibited.
5. When punching and shearing, you must always refuel the punching tools to prevent skewing.
6. Pay attention to the finger safety when feeding, especially when the sheet rushes to the end of the presser foot and cannot press on the sheet, punching, and shearing are prohibited.
7. It is forbidden to disassemble and proofread the cutting edge and die when driving. It is not allowed to strike punches, scissors, and other parts.
8. Strictly control the specification range of the sheet, and punching and shearing are strictly prohibited when it is exceeded.
9. Workplaces must not be piled up with other items and a lot of brewing materials and must be parked during adjustments and sweeps.
10. After the work is completed, the machine is shut down in time, powered off, and cleaned up.
Operating Steps of GLDMA iron worker machine
1 Check the power supply, the voltage is stable, there is no phase loss, the leakage protector and the air switch are in good condition.
2 Wiring, open the joint punching machine junction box, connect the wire, and close the door.
3 After the power is turned on, press down the foot switch and the machine will not operate. Exchange the power cord and check if the emergency stop switch is turned on.
4 Connect the footswitch.
5 At work, pay attention to turn off the power every time you change the mold during work
6 Turn off the switch after work is completed, turn off the power switch, remove the power cord, and clean the debris.
Maintenance
1 Operate strictly in accordance with the operating procedures.
2 According to the requirements of the lubrication chart, each time before starting the machine, timing, fixed point, and fixed amount of lubricant should be added, and the oil should be clean without precipitation.
3 Shears must always be kept clean, with some rust-proof grease not painted.
4 The lubrication oil in the motor bearing should be changed and filled regularly, and often check whether the work of the electrical part is normal, safe and reliable.
5 Always check if the shears, belts, handles, knobs, and keys of the shears are damaged. Replace them with serious wear and replace them with spare parts.
6 Regularly check the repair switch, insurance, handle and ensure its reliable operation.
7 Lubricate the machine tool and scrub the machine tool 10 minutes before work every day.

Labels:

Comments

Post a Comment

Popular posts from this blog

Fiber Laser Cutting Machine

Nowadays laser cutting machine is more and more widely used, as it is with high speed, high precision and automation. It can save manpower and improve production efficiency.  The laser is shot from laser generator, through optical system, focus to high power and density laser beam. The beam shoots on surface of workpiece and makes it reach melting point or boiling point, at the same time, the high pressure gas which is on the same axis with laser beam blow the melting or pneumatolytic metal away. That is the basic reason of laser cutting. According to the laser generator, there are two types – CO2 type & fiber type. The frequency of the CO2 laser requires higher wattage of lasers to penetrate through metals. CO2 laser systems are best suited to cutting wood, acrylic, plastic, and fabric.  Fiber laser cutting machine  is much more energy saving. In the situation that reaches same performance, whole fiber cutting can save around 70% energy than CO2 type. The wattage can...
40 comments
Read more

6mm Hydraulic Shearing Machine With Estun E21s

6mm is a common thickness in sheet metal manufacturing. 6mm  hydraulic shears  is also a popular size in shearing machine. GLDMA can offer 6mm*2500mm, 6mm-3200mm, 6mm*4000mm, 6*5000mm different sizes of worktable, to satisfy variety of plate cutting demands. GLDMA Q12K series swing shearing is standard with Estun E21s system, which can control backgauge and the ordinary motor or frequency converter. Finished parts count and 40 program store functions can support common cutting task much more continuous, so that improve daily producing efficiency and save labor cost. There are also other advanced  shearing machine controller  to choose, like Estun E200ps, Delem DAC 310s. E200ps can realize servo control on X axis (backgauge), the cutting speed and precision are in a higher level. DAC 310s is with control of blade clearance, and the program storage is improved to 100 steps each. Client can choose the suitable model based on their own requirement and budget. 6mm hydra...
12 comments
Read more

Automatic sheet metal bending machine

MB8 series sheet metal press brake with Delem DA56S CNC system Main motor: Siemens Germany Valve: Bosch Rexroth Germany Oil pump: Sunny America Oil tube connectors: EMB Germany Electrics: Schneider, France MB8 CNC Automatic 3+1 Axis Hydraulic Sheet Metal Press Brake Bending Machine With DA56S System Introduction 1. The design meets EU international streamlined design. The fuselage eliminates internal stress by annealing and ensures higher precision and strength. All machines are designed using SOLID WORKS 3D programming to make worktable high rigidity and the whole work More scientific. 2. The MB8 series automatic sheet metal electro-hydraulic bending machines use CNC control system (Delem DA56s from Holland) to help you increase your productivity and keep the lowest cost and lower maintenance costs.High quality and repetitive bending is obtained by using synchronized cylinders and valves (Bosch Rexroth from Germany). 3. The latest high frequency response hyd...
9 comments
Read more