Skip to main content

GILDE Hydraulic Guillotine Shears Safety Operation Regulations

GILDE Hydraulic Guillotine shears safety operation regulations

1. The operator must be familiar with the structure and performance of the machine;

2. Before working, it is necessary to carefully check whether each part of the shears is normal, whether the electrical equipment is in good condition, whether the lubrication system is unblocked, and whether the oil quantity is sufficient (after the start of the oil pump, check whether the valves and pipes are leaking).

3. At the same time, ensure that the working area is clean, clear tools, measuring tools and other debris and corner wastes (forbidden to store on the workbench) on the surface of the countertop and its surrounding areas to avoid accidents caused by rolling into the knife edge. The

4. Before the air-running test, it is necessary to use a manual work cycle to confirm the normal operation before starting the equipment.

5. The finger feeding by the shearer operator should keep a distance of at least 200mm from the scissors mouth, and leave the pressing device away. Do not insert his hand between the upper and lower blades to avoid accidents;

6, blade edge should be kept sharp, such as blade blunt or cracking phenomenon should be promptly replaced.

7. The screen-type oil filter mounted on the oil suction port of the oil pump should always be checked and cleaned so that the oil filter can maintain the required amount of oil. If the oil filter is blocked, the amount of oil passing through will be reduced, which will make the oil pump suck empty. The life of the pump.

8. The return cylinder must not be filled with oxygen, compressed air, or other flammable gases. Apply aeration tools slowly when filling with nitrogen. Pressure gas must be vented before removing the return cylinder to avoid accidents.

9. The shear clearance of the shears shall be adjusted according to the thickness of the sheet material. The blade shall be fastened firmly and the upper and lower blade surfaces shall be kept parallel. After adjustment, the manual test shall be applied.

10. In order to ensure safe operation, the pressing device shall firmly press the plate material during the cutting operation, and it shall not be allowed to cut under the pressure not tight. At the same time, it is forbidden to cut the laminated sheet material, and it is forbidden to trim the edge of the raw edge sheet material. It is forbidden to cut two kinds of sheet materials of different specifications and different materials at the same time.

11. It is not allowed to privately adjust other hydraulic valves except the throttle.

12. During operation, if abnormal noise or oil tank overheating is found, stop and check immediately (the maximum temperature of the tank does not exceed 60 degrees).

13. Clean the materials after the work is completed and routinely maintain the equipment.

Here with the link to show how to safety operation our Guillotine shearing machines: https://www.youtube.com/watch?v=WvKbnaawx6M

We GILDE company also can manufacture huge modes Guillotine shearing machines, like mode QC11K-20*2500mm，QC11K-20*320000mm，QC11K-20*4000mm and so on, welcome to inquiring from us anytime.

Labels:

Comments

  1. BEST KATHA GHOROctober 10, 2020 at 3:07 AM

    Really it was an awesome article. Thank you so much for the post it is very helpful, Keep posting such type of articles as Machining

    ReplyDelete
  2. ADI FREE PC SOLUTIONSDecember 28, 2020 at 5:32 AM

    I needed to thank you for this very good read!!

    I certainly enjoyed every bit of it. I have got you book marked to look at new things you post…

    microsoft office 2007 keys
    IDM
    Easeus Data Recovery
    Windows 7 activator
    4k video downloader
    Microsoft office 365
    Windows 10 activator
    xforce keygen

    ReplyDelete

Post a Comment

Popular posts from this blog

Fiber Laser Cutting Machine

Nowadays laser cutting machine is more and more widely used, as it is with high speed, high precision and automation. It can save manpower and improve production efficiency.  The laser is shot from laser generator, through optical system, focus to high power and density laser beam. The beam shoots on surface of workpiece and makes it reach melting point or boiling point, at the same time, the high pressure gas which is on the same axis with laser beam blow the melting or pneumatolytic metal away. That is the basic reason of laser cutting. According to the laser generator, there are two types – CO2 type & fiber type. The frequency of the CO2 laser requires higher wattage of lasers to penetrate through metals. CO2 laser systems are best suited to cutting wood, acrylic, plastic, and fabric.  Fiber laser cutting machine  is much more energy saving. In the situation that reaches same performance, whole fiber cutting can save around 70% energy than CO2 type. The wattage can range from 50
40 comments
Read more

How to Adjust the Clearance of Upper and Lower Blades of Hydraulic Guillotine

To many customers, they can easy to get how to adjust the clearance of upper and lower blades of small model  hydraulic guillotine shearing machines . How every, it's do hard for them to adjustment big models like QC11Y-40*2500 mm or QC11Y-40*3200mm. It is an important factor that affects the cutting quality and prolongs the service life of the blade. The correct adjustment of the blade thickness depends on the shear plate thickness. The machine tool converts the blade gap value to the plate material value directly on the gap dial. The clearance between the upper and lower blades of the shear should be the same throughout the entire length. This shear shall be equipped with a supplementary tool holder on the worktable to be used as a micro adjustment of the uniformity of the gap between the upper and lower blades. The minimum clearance before adjustment is 0.05 mm at the factory. The user should not change easily during normal use. After the blade is used for a certain period of
6 comments
Read more

6mm Hydraulic Shearing Machine With Estun E21s

6mm is a common thickness in sheet metal manufacturing. 6mm  hydraulic shears  is also a popular size in shearing machine. GLDMA can offer 6mm*2500mm, 6mm-3200mm, 6mm*4000mm, 6*5000mm different sizes of worktable, to satisfy variety of plate cutting demands. GLDMA Q12K series swing shearing is standard with Estun E21s system, which can control backgauge and the ordinary motor or frequency converter. Finished parts count and 40 program store functions can support common cutting task much more continuous, so that improve daily producing efficiency and save labor cost. There are also other advanced  shearing machine controller  to choose, like Estun E200ps, Delem DAC 310s. E200ps can realize servo control on X axis (backgauge), the cutting speed and precision are in a higher level. DAC 310s is with control of blade clearance, and the program storage is improved to 100 steps each. Client can choose the suitable model based on their own requirement and budget. 6mm hydraulic shearing usual
12 comments
Read more