Skip to main content

Common Failure Analysis of CNC Hydraulic Bending Machine

Failure 1: no pressure on the hydraulic system
  1. Whether the electromagnetic coil of the proportional overflow valve is electric, and whether the proportional electromagnetic coil voltage meets the requirements, for the above reasons, please check the relevant electrical reasons.
  2. Check whether the cartridge valve is stuck or whether the main valve core is jammed, and the damping holes are blocked. If this is the above reason, please remove the overflow valve to clean and reload.
  3. Three-phase power supply phase, leading to motor reversal.
Fault 2: the slide is fast and slow, and the time is too long
  1. Check whether the oil level of the oil tank is too low, and the filling port is not submerged.For the above reasons, the oil tank oil can be added to above 5mm above the filling mouth and the filling hole is completely submerged.
  2. Check whether the fast-forward speed is too fast, and the filling is insufficient.For the above reasons, the fast forward speed can be reduced by modifying the system parameters.
  3. Check whether the filling valve is fully opened, if it is because of the oil pollution, the valve core activity of the filling valve is not flexible and there is a lag phenomenon, which leads to insufficient filling.The filling valve needs to be reinstalled to make the valve core flexible.
Fault 3: the sliding block return normal, fast forward to normal, manual cannot slow down, folding plate weakness
  1. Check whether the "two-position four-way" reversing valve of the control liquid control oil circuit is working normally, and if it is, the filling valve is not closed, so that the upper chamber is connected with the fuel tank, and the pressure cannot be built.The reason that the valve cannot work properly is that there is no electricity or card to die.
  2. Check whether the filling valve is stuck. If so, please clean the filling valve and reinstall it to make the valve core flexible.

 You can find more good quality CNC Hydraulic Bending Machine at GLDMA.
Labels:

Comments

  1. UnknownMarch 26, 2018 at 8:48 PM

    Tel：+86-18055583445
    Whatsapp：+86-18055583445
    Skype：+86-18055583445
    Email：admin@gldma.com
    website: http://www.gldma.com

    ReplyDelete
  2. RevathyApril 18, 2018 at 2:33 AM

    All sites are working..This is great thing..A huge thanks from my side…:)

    Boom Lift

    ReplyDelete

Post a Comment

Popular posts from this blog

Fiber Laser Cutting Machine

Nowadays laser cutting machine is more and more widely used, as it is with high speed, high precision and automation. It can save manpower and improve production efficiency.  The laser is shot from laser generator, through optical system, focus to high power and density laser beam. The beam shoots on surface of workpiece and makes it reach melting point or boiling point, at the same time, the high pressure gas which is on the same axis with laser beam blow the melting or pneumatolytic metal away. That is the basic reason of laser cutting. According to the laser generator, there are two types – CO2 type & fiber type. The frequency of the CO2 laser requires higher wattage of lasers to penetrate through metals. CO2 laser systems are best suited to cutting wood, acrylic, plastic, and fabric.  Fiber laser cutting machine  is much more energy saving. In the situation that reaches same performance, whole fiber cutting can save around 70% energy than CO2 type. The wattage can range from 50
40 comments
Read more

How to Adjust the Clearance of Upper and Lower Blades of Hydraulic Guillotine

To many customers, they can easy to get how to adjust the clearance of upper and lower blades of small model  hydraulic guillotine shearing machines . How every, it's do hard for them to adjustment big models like QC11Y-40*2500 mm or QC11Y-40*3200mm. It is an important factor that affects the cutting quality and prolongs the service life of the blade. The correct adjustment of the blade thickness depends on the shear plate thickness. The machine tool converts the blade gap value to the plate material value directly on the gap dial. The clearance between the upper and lower blades of the shear should be the same throughout the entire length. This shear shall be equipped with a supplementary tool holder on the worktable to be used as a micro adjustment of the uniformity of the gap between the upper and lower blades. The minimum clearance before adjustment is 0.05 mm at the factory. The user should not change easily during normal use. After the blade is used for a certain period of
6 comments
Read more

6mm Hydraulic Shearing Machine With Estun E21s

6mm is a common thickness in sheet metal manufacturing. 6mm  hydraulic shears  is also a popular size in shearing machine. GLDMA can offer 6mm*2500mm, 6mm-3200mm, 6mm*4000mm, 6*5000mm different sizes of worktable, to satisfy variety of plate cutting demands. GLDMA Q12K series swing shearing is standard with Estun E21s system, which can control backgauge and the ordinary motor or frequency converter. Finished parts count and 40 program store functions can support common cutting task much more continuous, so that improve daily producing efficiency and save labor cost. There are also other advanced  shearing machine controller  to choose, like Estun E200ps, Delem DAC 310s. E200ps can realize servo control on X axis (backgauge), the cutting speed and precision are in a higher level. DAC 310s is with control of blade clearance, and the program storage is improved to 100 steps each. Client can choose the suitable model based on their own requirement and budget. 6mm hydraulic shearing usual
12 comments
Read more