Debug
1, The adjustment of the machine, before install, the first thing to adjust the machine performance, the process must be patient and careful to check the machine is used with ash and iron particles, such as the necessary cleaning, in order to reduce the trouble later.
2, Stroke adjustment, pay attention to check the thickness of the mold and check module is normal, the proportion of the up and down in a normal route for module to control the switch point, you must be aware of this.
3, The adjustment of stroke module, which is in view of the limit point adjustment module, the module on to the top, the switch is set up, and set aside the slider position, at the same time when the next to slow module, to better protect the machine and mold.
4. The adjustment of the gap is mainly to measure the distance between the module and the next module. The specific clearance is determined according to the folded sheet.
5, The adjustment of the Angle, the Angle adjustment has a certain relationship with the product, generally 90 ° die, the Angle must be greater than the Angle on both sides of the middle, then its elastic can be done according to the adjusting screw, when bending, can be through the pressure gauge pressure adjustment, avoid mould broken.
Operate
Step1, Turn on the power, open the switch key of control panel, then press the pump to start, so you hear the sound of the pump rotation.
Step2, Stroke adjustment, we should pay more attention to adjust the stroke when we use press brake, before bending, the machine must be tested. There is 1mm gap between punching and lower die, otherwise it will bring damage to the mold and the machine. There are electric quick adjustment and manual adjustment.
Step3, Choosing V-notching, the V-notching width is 8 times thickness of the plate, For example, when we bend 4mm plate,we need to choose 32mm V-notching.
Step4, Back gauge adjustment, there are quick electrical adjustment and slow manual adjustment. They are similar as the back gauge adjustment of shearing machine.
Step5, Pressing foot switch to start bending, bending machine and cutting plate machine is different, you can release at any time, release the foot bending machine will stop, continue to steping the foot switch the machine will go on work.
1, The adjustment of the machine, before install, the first thing to adjust the machine performance, the process must be patient and careful to check the machine is used with ash and iron particles, such as the necessary cleaning, in order to reduce the trouble later.
2, Stroke adjustment, pay attention to check the thickness of the mold and check module is normal, the proportion of the up and down in a normal route for module to control the switch point, you must be aware of this.
3, The adjustment of stroke module, which is in view of the limit point adjustment module, the module on to the top, the switch is set up, and set aside the slider position, at the same time when the next to slow module, to better protect the machine and mold.
4. The adjustment of the gap is mainly to measure the distance between the module and the next module. The specific clearance is determined according to the folded sheet.
5, The adjustment of the Angle, the Angle adjustment has a certain relationship with the product, generally 90 ° die, the Angle must be greater than the Angle on both sides of the middle, then its elastic can be done according to the adjusting screw, when bending, can be through the pressure gauge pressure adjustment, avoid mould broken.
Operate
Step1, Turn on the power, open the switch key of control panel, then press the pump to start, so you hear the sound of the pump rotation.
Step2, Stroke adjustment, we should pay more attention to adjust the stroke when we use press brake, before bending, the machine must be tested. There is 1mm gap between punching and lower die, otherwise it will bring damage to the mold and the machine. There are electric quick adjustment and manual adjustment.
Step3, Choosing V-notching, the V-notching width is 8 times thickness of the plate, For example, when we bend 4mm plate,we need to choose 32mm V-notching.
Step4, Back gauge adjustment, there are quick electrical adjustment and slow manual adjustment. They are similar as the back gauge adjustment of shearing machine.
Step5, Pressing foot switch to start bending, bending machine and cutting plate machine is different, you can release at any time, release the foot bending machine will stop, continue to steping the foot switch the machine will go on work.
Comments
Post a Comment